Pipeclamp Components

Viewing 72 of 320.

Sort by

£2.30

(ex. VAT)

Hook 90°. Similar to tube coupling type 182, but better suited for making coat hangers and the like.

182 Wall Mount with Hook ( 33.7mm Round Black)

From £2.30

(ex. VAT)

Chain hook. Used to locate chains across openings. Not ideal for permanent chain location. Recommended that one end of the chain is fixed using a Key Clamp and held in place with a nut and bolt.

From £2.33

(ex. VAT)

An inline external tube connector for joining two tubes of the same diameter. This key clamp fitting is not recommended to be used in high load applications. For a smooth inline joint the key clamp fitting 150 can be used.

199 Single Lugged Bracket ( 33.7mm Round Self Colour)

£2.36

(ex. VAT)

Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors. The tube cannot be joined within the fitting.

199 Single Lugged Bracket ( 33.7mm Round Black)

From £2.36

(ex. VAT)

Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors. The tube cannot be joined within the fitting.

183 Wall Mount with Straight Hook (Square 40 x 40)

£2.45

(ex. VAT)

Straight hook. Used to locate chains across openings. Not ideal for permanent chain location. Recommended that one end of the chain is fixed using a Key Clamp and held in place with a nut and bolt.

182 Wall Mount with Hook ( Square 25 x 25 Black)

£2.50

(ex. VAT)

Chain hook. Used to locate chains across openings. Not ideal for permanent chain location. Recommended that one end of the chain is fixed using a Key Clamp and held in place with a nut and bolt.

182CH Coat Hook Key Clamp (33.7mm Round Black)

From £2.50

(ex. VAT)

Hook 90°. Similar to tube coupling type 182, but better suited for making coat hangers and the like.

182CH Coat Hook Key Clamp (33.7mm Round Self Colour)

£2.50

(ex. VAT)

Hook 90°. Similar to tube coupling type 182, but better suited for making coat hangers and the like.

From £2.53

(ex. VAT)

A 90° offset crossover fitting. The tube is unable to be jointed within this fitting. Ideal applications are for racking systems or offset guardrail. Where dimension ‘D’ indicates two figures, the first figure refers to tube ‘A’, second refers to tube ‘B’.

From £2.54

(ex. VAT)

An inline internal tube connector for joining two tubes of the same diameter. This key clamp fitting can only be used with 3.2mm wall thick tube. This fitting is not recommended for high or tensile load applications.

£2.59

(ex. VAT)

Non structural male locating flange.

From £2.71

(ex. VAT)

Key Clamp fitting typical use is on straight and level guardrail for connecting the mid/lower rail to the vertical at a 90 corner. Can also be used in a similar way on other rectangular structures (Kee Klamp compatible 21).

Square 25 x 25 x 2.0 2 Way Elbow Tube Connector

£2.75

(ex. VAT)

Two piece clip together plastic moulding.
Provides butt connection for square tubes.

173M Single Male Swivel Key Clamp (Square 40 x 40)

£2.75

(ex. VAT)

Key Clamp Single male fitting with only 1 lug.

From £2.77

(ex. VAT)

Key Clamp fitting typical use is to connect the end vertical to the top rail in straight and level guardrail. Can also be used to create a 90 tube bend.(Kee Klamp compatible 15)

119 Single Lugged Bracket ( Square 40 x 40) [duplicate]

£2.79

(ex. VAT)

Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors. The tube cannot be joined within the fitting.

From £2.80

(ex. VAT)

shown, priced and sold as a single fitting but normally used in pairs to create angles between 85° and 235°. A central tube is required to join the (Key Clamp) fittings together to create the angle. When working out the correct tube length dimension ‘C’ should be subtracted.

173M Single Male Swivel Key Clamp [duplicate]

From £2.80

(ex. VAT)

Key Clamp Single male fitting with only 1 lug.

From £2.84

(ex. VAT)

Wall mounting bracket for handrails. Can also be used to tie back structures to wall or to hold kicking plates on a guardrail. This Key Clamp fitting has countersunk holes and is not recommended as a structural fixing. This fitting has no ability to join tubes.

From £2.84

(ex. VAT)

A combination fitting designed for use in the construction of racking systems. The fitting enables the connection of a vertical upright at 90° to 2 horizontal rails, 1 being the tie rail, the other being the load rail. On pallet racking the upright normally has the load rail on the inside, whilst for shelved racking the upright normally has the load rail on the outside.

From £2.90

(ex. VAT)

A Key Clamp 90 joint between a vertical and two horizontals. Typical use on straight and level guardrail to connect the mid/lower rails to the upright (Kee Klamp compatible 26). The vertical must remain continuous with cross rails cut. Normally used in conjunction with the Key Clamp fitting 104 Long Tee.

From £2.98

(ex. VAT)

An internal swivel tee used in conjunction with other Key Clamp fittings in the range to create a 360° swivel joint. Ideal use on handrail or offset guardrailing down variable angled slopes. Eliminates the requirement for specialised angle fittings.

Square 25 x 25 x 2.0 3 Way Elbow Tube Connector

£2.98

(ex. VAT)

Two-piece clip together plastic molding.

Provides corner connection for square tubes.