Square System 25x25

Viewing 24 of 35.
grid
list
£1.35
(ex. VAT)

A plastic stop end for use in the end of tubes. This stop end cap can be used in either medium or heavy gauge tube. This is only a friction fit and for a more permanent fix an adhesive is recommended.



£1.80
(ex. VAT)

Hexagonal key. The allen key is the only tool required to tighten up a Pipeclamp fitting. The use of the dual ratchet Pipeclamp  is recommended to achieve the required torque.

£2.15
(ex. VAT)

Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors. The tube cannot be joined within the fitting.

£2.15
(ex. VAT)

Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors. The tube cannot be joined within the fitting.

£2.25
(ex. VAT)

Chain hook. Used to locate chains across openings. Not ideal for permanent chain location. Recommended that one end of the chain is fixed using a Key Clamp and held in place with a nut and bolt.

£2.45
(ex. VAT)

Straight hook. Used to locate chains across openings. Not ideal for permanent chain location. Recommended that one end of the chain is fixed using a Key Clamp and held in place with a nut and bolt.

£2.75
(ex. VAT)

Key Clamp Single male fitting with only 1 lug.

£3.15
(ex. VAT)

Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors. The tube cannot be joined within the fitting.

£3.50
(ex. VAT)

An inline external tube connector for joining two tubes of the same diameter.

£3.75
(ex. VAT)

Key Clamp Single male fitting with only 1 lug.

£4.00
(ex. VAT)

Wall mounting bracket for handrails. Can also be used to tie back structures to wall or to hold kicking plates on a guardrail. This Key Clamp fitting has countersunk holes and is not recommended as a structural fixing. This fitting has no ability to join tubes.

£4.12
(ex. VAT)

A 90 deg. tee connection between two tubes. Typical use is on straight and level guardrail to connect the vertical to the top rail or end/mid rail to the vertical. This Key Clamp fitting cannot be used to join tubes in the top of the short tee.

£4.45
(ex. VAT)

Often used for mounting boards practically flush with tubes. Fixing holes suit a wide range of common mechanical and chemical masonry anchors. The tube cannot be joined within the fitting.

£4.90
(ex. VAT)

A Key Clamp 90 joint between a vertical and two horizontals. Typical use on straight and level guardrail to connect the mid/lower rails to the upright (Kee Klamp compatible 26). The vertical must remain continuous with cross rails cut.

£5.69
(ex. VAT)

Key Clamp fitting typical use is on straight and level guardrail for connecting the mid/lower rail to the vertical at a 90 corner.

£5.75
(ex. VAT)

Key Clamp Complete single swivel. The swivel has a travel of approximately 85° from the horizontal in both vertical directions.(Kee Klamp compatible C50)

£5.95
(ex. VAT)

Complete locating swivel. Swivel has a travel of approximately 85 from the vertical in each direction.

£6.00
(ex. VAT)

3 way tee used to join 3 tubes at 90° to each other with the vertical passing through the fitting. Typical use would be on structures such as market stall or play frames.

£6.19
(ex. VAT)

Key Clamp fitting typical use is to connect the end vertical to the top rail in straight and level guardrail. Can also be used to create a 90 tube bend.(Kee Klamp compatible 15).

£6.50
(ex. VAT)

A structural base plate for all level aspects of vertical post support. This key clamp fitting when used as a base plate for guardrailing should always be positioned with the holes across the line of the guardrail to give maximum strength. The holes in the base plate are large enough to enable the use of mechanical or chemical anchor fixings.

£6.90
(ex. VAT)

A 90 deg. tee connection between 2 tubes. Typical use is on straight and level guardrail to connect the vertical to the top rail. This Key Clamp fitting can be used to join tubes in the top of the twin grubscrew long tee.

£7.00
(ex. VAT)

A combination fitting designed for use in the construction of racking systems. The fitting enables the connection of a vertical upright at 90° to 2 horizontal rails, 1 being the tie rail, the other being the load rail. On pallet racking the upright normally has the load rail on the inside, whilst for shelved racking the upright normally has the load rail on the outside.

£7.25
(ex. VAT)

A 3 way enclosed 90 corner joint. Typical use is on straight and level guardrail at a 90 corner where an upright is in position. This Key Klamp fitting can also be used to create enclosed corner joints in other square structures such as benches etc.

£7.25
(ex. VAT)

Our easy to assemble, do it yourself - Square system range of tube and fittings are perfect for a wide range of applications.

Galvanised Square Clamp fittings, are black malleable fittings with a galvanised finish. All clamps come supplied with grub screws.

Fittings can be tightened using a standard allen hex key.

And combined with galvanised box section (square tube), make it the perfect "DIY kit" for many uses including shelving, furniture, signage, structures plus many more.

Availability

We have all the most popular items in stock & in size 25mm square avaialable off the shelf.